Download Article

Download Article

When you smoke with water pipes, resin will build up inside over time, which will then constrict airflow. It's pretty hard to gain access to scrub this away, but thankfully you don't need to. What you need to do first is take your pipe apart into its individual pieces. Then you bag these individually in separate plastic bags filled with a cleaning solution. To clean, all you need to do is shake these bags up and then rinse off all your pieces before putting them back together.

  1. 1

    Let your pipe cool down. If you intend to clean it right after smoking, give it a chance to cool off. Wait for all parts to be safe enough to touch. Avoid burning yourself and/or dropping and breaking your pipe.

  2. 2

    Empty its contents. If cleaning right after use, make sure all flames have died out before proceeding. Then dump any ash or other contents in the pipe's bowl into the trash. Next, empty the spent water from the base into the sink or toilet.

    Advertisement

  3. 3

    Take the pipe apart. Take the bowl out of the base. If the pipe has a washer, remove that, too. Also detach any other additional parts that it may have. These could include:

    • Additional parts that may be removable may include percolators, ice catchers, and coils.

  4. 4

    Inspect pieces for damage. As you disassemble your pipe, check for flaws, like chipped or cracked glass and rubber. Replace damaged pieces rather than just clean them to keep your pipe safe and effective.

    Advertisement

  1. 1

    Rinse the pieces in the sink. Give each one a few passes under running water. Wash away any loose ash, resin, or other materials. Make the cleaning solution that you'll be using momentarily that much more effective by giving it less stuff to get rid of.

  2. 2

    Add salt to the base. You'll be bagging each individual piece in a moment, and then adding salt to each bag. However, keep in mind that the base is much bigger than rest, and simply adding salt after you bag won't ensure that any reaches the base's interior. So pour some into the base now before you bag it.

  3. 3

    Bag each piece individually. Place each one in its own sealable, watertight plastic bag. Do not combine multiple pieces in one bag. You'll be shaking these up soon, so don't risk banging glass pieces together, since this will damage them. However:

  4. 4

    Add rubbing alcohol and salt to each bag. Fill the bag with enough rubbing alcohol to completely immerse the piece inside. Then add enough salt to cloud the liquid slightly. Err on the side of too little salt, rather than too much, since too much will result in clumps that may cause blockage in various pieces.

    • 70 to 91% isopropyl alcohol is usually sufficient. However, extremely dirty pipes might require 100% acetone or nail polish remover.
    • As an alternative, you can also try mouthwash, since its aftertaste is far more pleasant than any that might linger from rubbing alcohol or nail polish remover.

    Advertisement

  1. 1

    Soak very soiled pieces. If tons of resin have built up over time, give each affected piece time to absorb the cleaning solution. Let them soak in the alcohol for up to an hour, or even longer if necessary, before proceeding. Give the resin's bond a chance to break apart and weaken.

  2. 2

    Shake each bag vigorously. First, double-check the bag's seal to avoid spills. Then shake each bag hard for 30 to 40 seconds, or even longer if needed. This will shake the loosened resin free, and also cause the abrasive salt to scratch away at the more stubborn bits.[1]

  3. 3

    Empty and rinse lightly soiled pipes. If desired, pour the solution from each bag into a sealable container for reuse in the future. Then, as long as your pipe wasn't too dirty to begin with, take each piece and rinse it under hot running water if your pipe was only slightly dirty at the start. With the base, pour water in through the mouthpiece so it drains out of the hole(s) at its bottom to avoid unpleasant aftertastes where youre lips will touch it.

  4. 4

    Soak very dirty pipes in a container. If your pipe was very soiled at the start, don't rinse it off in the sink. Instead, fill a container with hot water and submerge each piece to rinse them off. Then empty the dirty water into the toilet and flush. Avoid using the sink's drain, since resin is more likely to stick to these pipes and cause future clogs.

  5. 5

    Repeat if needed. Once you've rinsed off each piece, give it a look over. Expect it to possibly need more than one bag-and-shake if it had a lot of resin to start. If the inside of the base and its tube appear particularly dirty, try:

    • Plugging its holes with cotton balls or similar materials, adding salt and rubbing alcohol to it directly, and shaking it vigorously with your hands covering all openings.

  6. 6

    Wipe away residue. Inspect each piece for any crud that may have clung on during rinses. Soak q-tips in rubbing alcohol and use these to remove them. If these are too short to reach inside any piece, improvise by attaching cotton swabs or balls to a chopstick or something similar.

  7. 7

    Put your pipe back together and rinse. Once everything is cleaned to your satisfaction, put all your parts back into place. Give it a final rinse under hot running water. It may seem like overkill, but this will reduce the chance of any unpleasant aftertaste.

    Advertisement

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Thanks for submitting a tip for review!

Things You'll Need

  • Sealable plastic bags
  • Rubbing alcohol
  • Salt
  • Water
  • Sink
  • Toilet (optional)
  • Container (optional)
  • Q-tips
  • Chopsticks and cotton swabs (optional)

References

About This Article

Thanks to all authors for creating a page that has been read 17,358 times.

Did this article help you?